TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 1 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com applications ? ? ? ? ? ? ordering information part no. description TQP9321 0.5 w small cell pa TQP9321 - pcb evaluation board standard t/r size: 2500 pcs. on a 13 reel product features ? : 1.8? C ?2.17 ghz ? ? ? ? ? ? ? ? ? ? ? ? ? ? quiescent current: 110?ma ? ? single supply voltage: +5?v ? ? functional block diagram general description the tqp 9321 is a high - efficiency , two - stage power amplifier with integrated bias and temperature control circuits in a low - cost surface - mount package . this 0.5 watt power amplifier is ideal for small cell base station applications . TQP9321 provides high gain (30?db) and +27?dbm linear distortion correction over the 1.8? C ?2.2 ?50?dbc aclr at +27?dbm output power us is bias adjustable allowing the amplifiers ? ? .5? ? C ? ? C ? pin configuration pin no. label 1 v bias 2 v cc 3, 4, 5, 6, 8, 9, 10 n/c 7 rfout 11 v pd2 12 v pd1 13 rfin backside pad rf/dc ground p i n 1 r e f e r e n c e m a r k p a c k a g e t o p s i d e e x p o s e d b a c k s i d e p a d g n d v b i a s v c c n / c r f o u t r f i n v p d 1 n / c n / c n / c n / c n / c n / c v p d 2 1 2 1 9 6 7 1 1 4 1 3 2 1 0 3 5 8 a m p 1 a m p 2 m a t c h i n g n e t w o r k m a t c h i n g n e t w o r k
TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 2 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com absolute maximum ratings parameter rating storage temperature ? ? cc ) +6?v cw, 50 ? , t=25 ? c +10?dbm operation of this device outside the parameter ranges given above may cause permanent damage. recommended operating conditions parameter min typ max units v dd +5 v t amb ? 6 hours mttf + 175 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. electrical specifications test conditions unless otherwise noted: v cc ? = ? +5?v, v pd1 ? = ? v pd2 ? = ? +5?v, temp. ? = ? +25?c. parameter conditions min typ max units operational frequency range 1800 2170 mhz output channel power +27 dbm gain 1805? C ?1880 ? mhz 28.1 30 db 1930? C ?1990 ? mhz 27.1 29 db 2110? C ?2170 ? mhz 27. 1 29 30. 8 db gain temperature coefficient - 0.024 db/ c aclr uncorrected see note 1 - 35 dbc aclr corrected see note 1 - 50 dbc power added efficiency 1805? C ?1880?mhz, see note 1 29 % 1930? C ?1990 ? mhz, see note 1 28 % 2110? C ?2170?mhz, see note 1 27 % output p3db 1805? C ?1880?mhz +33.6 +34.7 dbm 1930? C ?1990 ? mhz +33.6 +34.7 dbm 2110? C ?2170?mhz +33. 6 +34.7 dbm p3db temperature coefficient - 0.008 dbm/ c noise figure 3.5 db quiescent current, i cq 90 110 13 6 ma reference current , i pd 2 ma operational current, i cc pout = +27?dbm pout = +26?dbm signal : wcdma 1c, par = 8?db 10:1 C thermal resistance, jc module (junction to case) 27 c/w notes: 1. using lte signal, 20?mhz/carrier, ibw = 18.02?mhz, par 7.5?db, pout = +27?dbm. 2. items in min/max columns in bold at guaranteed by production test at 2.14?ghz. 3. items in min/max columns that are not a bold font are guaranteed by design characterization.
TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 3 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com p erformance plots 16 18 20 22 24 26 28 30 32 34 36 20 22 24 26 28 30 32 34 36 gain (db) pout (dbm) gain vs. output power vs. frequency 1800 mhz 1900 mhz 2000 mhz 2140 mhz 2170 mhz temp.=+25 c 16 18 20 22 24 26 28 30 32 34 36 20 22 24 26 28 30 32 34 36 gain (db) pout (dbm) gain vs. output power vs. temperature +85 c +25 c ?40 c f = 2140 mhz cw 0 5 10 15 20 25 30 35 40 45 50 55 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 efficiency (%) pout (dbm) efficiency vs. output power vs. frequency 1800 mhz 1900 mhz 2000 mhz 2140 mhz 2170 mhz temp.=+25 c 0 5 10 15 20 25 30 35 40 45 50 55 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 efficiency (%) pout (dbm) efficiency vs. output power vs. temperature +85 c +25 c ?40 c f = 2140 mhz cw -65 -60 -55 -50 -45 -40 -35 19 20 21 22 23 24 25 26 27 28 29 acpr1(dbc) pout (dbm) acpr vs. output power vs. frequency 1.84 ghz dpd 1.96 ghz dpd 2.14 ghz dpd 1.84 ghz no dpd 1.96 ghz no dpd 2.14ghz no dpd temp.=+25 c signal : lte 20mhz, par = 7.5db channel bw utra, ibw = 3.84mhz dpd polynomial order : 11 -65 -60 -55 -50 -45 -40 -35 19 20 21 22 23 24 25 26 27 28 29 acpr1(dbc) pout (dbm) acpr vs. output power vs. temperature +85 c +25 c ?40 c signal : lte 20mhz, par = 7.5db channel bw utra, ibw = 3.84mhz vcc = 5v, frequency : 2140mhz dpd polynomial order : 11 -60 -55 -50 -45 -40 -35 -30 19 20 21 22 23 24 25 26 27 28 29 acpr1(dbc) pout (dbm) acpr vs. output power vs. frequency 1.84 ghz dpd 1.96 ghz dpd 2.14 ghz dpd 1.84 ghz no dpd 1.96 ghz no dpd 2.14ghz no dpd temp.=+25 c signal : lte 20mhz, par = 7.5db channel bw eutra, ibw = 18mhz dpd polynomial order : 11 -60 -55 -50 -45 -40 -35 -30 19 20 21 22 23 24 25 26 27 28 29 acpr1(dbc) pout (dbm) acpr vs. output power vs. temperature +85 c +25 c ?40 c signal : lte 20mhz, par = 7.5db channel bw eutra, ibw = 18mhz vcc = 5v, frequency : 2140mhz dpd polynomial order : 11 0 5 10 15 20 25 30 35 40 19 20 21 22 23 24 25 26 27 28 29 efficiency (%) pout (dbm) efficiency vs. output power vs. temperature +85 c +25 c ?40 c signal : lte 20mhz, par = 7.5db channel bw eutra, ibw = 18mhz vcc = 5v, frequency : 2140mhz dpd polynomial order : 11 -60 -55 -50 -45 -40 -35 -30 18 19 20 21 22 23 24 25 26 27 28 29 aclr (dbc) pout (dbm) aclr vs. pout 1805 mhz 1845 mhz 1880 mhz temp.=+25 c signal : lte 20mhz, par = 7.5db channel bw eutra, ibw = 18mhz dpd polynomial order : 11 -60 -55 -50 -45 -40 -35 -30 18 19 20 21 22 23 24 25 26 27 28 29 aclr (dbc) pout (dbm) aclr vs. pout 1930 mhz 1960 mhz 1990 mhz temp.=+25 c signal : lte 20mhz, par = 7.5db channel bw eutra, ibw = 18mhz dpd polynomial order : 11 -60 -55 -50 -45 -40 -35 -30 18 19 20 21 22 23 24 25 26 27 28 29 aclr (dbc) pout (dbm) aclr vs. pout 2110 mhz 2140 mhz 2170 mhz temp.=+25 c signal : lte 20mhz, par = 7.5db channel bw eutra, ibw = 18mhz dpd polynomial order : 11
TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 4 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com TQP9321 - pcb evaluation board bill of material TQP9321 - pcb ref des value description manuf. part number n/a n/a printed circuit board 1109803 u1 n/a high efficiency 2 - stage pa triquint TQP9321 r4 0 ? resistor, chip, 0 603 , 5% various r3 100 ? resistor, chip, 0 603, 1 % various c7 0.1 ? uf capacitor, chip, 0 603 , 5 % various c6 10 ? uf capacitor , chip, 6032, 10% , tantalum various c3, c5 100 ? pf capacitor , chip, 0603, npo/cog, 5% various r2 750 ? resistor, chip, 0 603 , 5%, 1/16w various r1 5.9 ? k resistor, chip, 0 603, 5% , 1/16w various c1, c2, c4 do not place 1 2 1 9 6 7 1 1 4 1 3 2 1 0 3 5 8 a m p 1 a m p 2 m a t c h i n g n e t w o r k m a t c h i n g n e t w o r k j 2 r f o u t p u t j 1 r f i n p u t c 6 1 0 u f j 3 + 5 v c 7 0 . 1 u f r 2 7 5 0 ? r 1 5 . 9 k ? j 5 + 5 v c 3 1 0 0 p f c 5 1 0 0 p f r 3 1 0 0 ? r 4 0 ? j 4 j 1 j 2 j 3 j 6 j 4 j 5 r 4 r 3 c 5 r 2 r 1 c 7 c 6 u 1 c 3
TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 5 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com pin configuration and description pin no. label description 1 v bias provides reference voltage for internal active biasing circuit 2 v cc dc voltage supply connection 3, 4, 5, 6, 8, 9, 10 gnd/nc no internal connection. provide grounded land pads for pcb mounting integrity. 7 rfout rf o utput pin. the dc is internally blocked at this pin. 11 v pd2 power down for amp 1. this voltage adjusts for the current draw in amp 1. 12 v pd1 power down for amp 2. this voltage adjusts for the current draw in amp 2. 13 rfin rf i nput pin. the dc is internally blocked at this pin. backside pad rf/dc gnd rf/dc ground. use recommended via pattern to minimize inductance and thermal resistance; see pcb mounting pattern for suggested footprint. p i n 1 r e f e r e n c e m a r k p a c k a g e t o p s i d e e x p o s e d b a c k s i d e p a d g n d v b i a s v c c n / c r f o u t r f i n v p d 1 n / c n / c n / c n / c n / c n / c v p d 2 1 2 1 9 6 7 1 1 4 1 3 2 1 0 3 5 8 a m p 1 a m p 2 m a t c h i n g n e t w o r k m a t c h i n g n e t w o r k
TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 6 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com package marking and dimensions marking: part identifier C C notes: 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec standard mo - 229. 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp - 012. 9321 yyww aaxxxx top view 0.920.08 0.10 c 4.50 4.500.1 2.25 3.500.1 1.75 2x 0.10 c 2x 0.10 c b a pin #1 locator side view bottom view 3.5000.1 1.080 1.000 2.000 1.000 2.000 0.680 1.080 0.750 1.500 2.000 1.080 0.500 1.000 1.500 2.000 4.5000.10 1.480 1.480 (1x) shape 0.10 c a b pin1 (10x) 0.270x x 0.340y 0.10 c a b (1x) 0.770x x 0.340y 0.10 c a b (1x) 1.270x x 0.340y 0.10 c a b c
TQP9321 high efficiency 0.5?w small cell pa datasheet: rev. h 04 - 10 - 15 - 7 of 7 - disclaimer: subject to change without notice ? 2015 triquint semiconductor, inc. www.triquint.com / www.qorvo.com contact information for the latest specifications, additional product information, worldwide sales and distribution locations: web: www.triquint.com tel: 877 - 800 - 8584 email: customer.support@qorvo.com for information about the merger of rfmd and triquint as qorvo: web: www.qorvo.com for technical questions and application information: email: sjcapplications.engineering@qorvo.com product compliance information esd sensitivity ratings caution! esd - sensitive device esd class : 2 volt. range : 2000 ? ? 1000 ? solderability compatible with both lead - free (260 ? ? rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipm ent). this product also has the following attributes: ? ? ? ? 15 h 12 br 4 0 2 ) free ? ? msl rating msl rating: msl3 test: 260 ? important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information contained herein is provid ed "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant informa tion before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with r egard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure w ould reasonably be expected to cause severe personal injury or death.
|
